Most warehouses think hardest about pallet racking inspection at two moments. One is when the insurer asks for the last report, and the other is the morning after a forklift clips an upright, a vertical steel post of a frame.
This guide sets out how pallet racking inspection in Ireland works. It covers how often to check, who can do it, what gets looked at and what the colours on a report mean. It also covers load signs and bolting, and ends with a free weekly checklist to print.
The 12-month expert visit people quote comes from the European standard, and it sits on top of weekly checks your own team can do. We supply the racking and the guards and fixings that inspection reports often call for.
Estimated reading time: 10 minutes
How often should warehouse racking be inspected?
Your team should check warehouse racking each week, and a trained inspector should look at it at least once a year. Anyone who spots damage should report it straight away. That’s the pattern in EN 15635, the European racking standard, which Ireland adopted as I.S. EN 15635:2008. SEMA, the UK trade body for racking makers, uses the same levels, and the table below shows who does each one.
| Level | Who does it | How often | What it catches |
|---|---|---|---|
| Report it now | Anyone who sees or causes damage | The moment it happens | A truck strike, a beam knocked loose |
| Regular check | A trained person on your staff | Weekly, or as your risk assessment says | New knocks, before stock goes back on |
| Expert visit | A trained racking inspector | At least once a year | Faults found, rated in a written report |
How often the expert comes depends on how hard your racking works. SEMA’s guide to pallet racking inspections puts the expert visit at once or twice a year, depending on the risk assessment. If trucks work the aisles most of the day, ask your inspector whether twice a year suits you.
When does racking need a check outside the schedule?
Irish law calls for an extra racking check outside the normal schedule when any of five things happens, even if the last report is recent. The list below sets them out.
- When racking is first put up, before it’s loaded.
- When it’s put up at a new site or in a new spot.
- After changes to it, such as a re-layout or level height changes
- After an accident, such as a known truck strike.
- After a long spell out of use.
Moving beam levels to fit a new pallet height is likely to count as a change, so treat it as one.
How long do racks last?
SEMA says it’s perfectly possible for a racking installation to last the entire lifetime of a business, as long as it’s used the way it was designed. Pallet racking has no set lifespan.
Inspection decides when a bay is done, and a red rating takes it out at any age.
Second-hand racking needs the same checks. Once it’s up at your site, the law wants it inspected before it’s loaded. SEMA warns used racking can easily be over 10 years old, and any part you swap must be approved for that system. Find out the make before you buy. It’s also wise to ask the seller for the latest report. Note: pre-owned pallet racking does not come certified like new pallet racking.
Is racking inspection a legal requirement in Ireland?
Irish law does require racking inspection, though it asks for checks from time to time rather than once a year.
Racking is generally treated as work equipment under the General Application Regulations 2007. Where it can take damage that makes it unsafe, a competent person has to inspect it at intervals. You’ve got to write down the results and keep them for five years, ready for any staff who ask or an inspector from the Health and Safety Authority (HSA). The law sets no annual certificate and no fixed gap between checks.
The HSA’s fact sheet on falling objects is just as plain. It says ‘Racking or shelves must be checked regularly for damage’ and that if damaged ‘they must not be used until replaced or repaired.’ It doesn’t set a gap either.
People searching for HSE racking rules here want the HSA, because the HSE runs the health service and the HSA covers safety at work.
So is the yearly expert visit optional?
The yearly expert visit isn’t optional in practice, because I.S. EN 15635 puts expert checks no more than 12 months apart and it’s what racking inspectors work to. Our guide to what EN 15635 means for your warehouse covers the standard in more detail.
Insurers often want proof you follow the standard, even where the law says nothing. We’ve set out how that works in the building codes and insurance rules that apply to pallet racking in Ireland.
Who can carry out racking inspections?
A competent person carries out racking inspections, and the law leaves you to judge who that is by training and experience, since it names no single course. In practice the job splits two ways.
The weekly check belongs to someone on your team who’s been trained to do it. SEMA calls them the PRRS, the person responsible for racking safety, and EN 15635 calls the same role the PRSES. Pick someone who’s on the floor every day and ask whoever drives the reach truck which uprights take the knocks.
SEMA says the expert can come from inside your own firm or from outside it. SEMA also trains and approves inspectors, called SARIs. When you book one, ask if they work to I.S. EN 15635 and SEMA’s rating method, and ask to see a sample report.
What does a pallet racking inspection check?
A pallet racking inspection looks at the uprights, beams and pins, bracing, base plates, load signs and how each bay is loaded. Rack inspections cover the same parts each week and at the yearly visit, but the expert goes on to rate each fault. The list below shows what each check looks for.
- Uprights near the floor, where most forklift damage lands. The HSA’s code of practice on industrial trucks lists truck damage to racking as one of the most common incidents.
- Beams and connectors, to check each beam (the horizontal bar a pallet sits on) sits level and still has its locking pin.
- Frame bracing, the cross members that tie the two uprights of a frame together.
- Base plates and floor fixings, looking for lifted feet or missing bolts.
- Load signs and labels, which should be easy to read and right for how each bay is set up now.
- How the racking is loaded, such as pallets hanging over the edge or heavy loads sitting high.
Our rule for staff checks is that if a dent’s deeper than the steel itself, that bay comes out of service until someone’s checked it properly. The rule is in our guide to what to look for in a shelving safety check, along with the signs to look for on each part.
Why do missing safety pins matter so much?
A beam with no locking pin can lift out of its slot when a pallet or a fork hits it from below, which is why missing safety pins matter. Pins come with each new beam and belong in every one. Check them again after any re-layout.
The pin has to match the make of your racking. We’re the sole Irish distributor of Kimer, a Spanish manufacturer with over 50 years’ experience. So if you run Kimer racking, our Kimer pallet racking locking pins are the ones to fit. They come in packs of 50, with one pin going in each beam end connector. On racking from another maker, check which pin that system uses before you order.
Which guards stop the next knock?
Guards fitted low on the uprights and across run ends take the next knock instead of the racking, because that’s where trucks hit. They don’t fix the habit behind the damage, so pair them with a word to the drivers.
Our Single Upright Flat Protector stands 400mm tall and the Single Upright Angle Protector 420mm. The Single Upright Angle Reinforcement 100mm protects the upright itself.
In cold stores, the 120mm HDPE Single Upright Protector fits uprights from 100mm to 120mm wide and works down to -40°C.
The end of a run takes knocks too, and the Frame Protector Guard Single 1200mm is a 100mm-high steel rail that sits across it. Crash stops and barriers for busier aisles are in our safety and protection range.
Do load signs have to be on racking in Ireland?
Load signs have to be on racking in Ireland, because the HSA’s falling-objects guidance says the maximum safe load ‘must be prominently marked on all racks’.
SEMA’s guidance on load notices says a notice should show the limits for that racking and some basic safety rules. It should also give the supplier’s contact details. SEMA’s technical FAQ adds that its approved inspectors will rate a black-and-white notice as amber, because the notice should be in colour. When your beam levels change, check the sign still matches them.
Should racking be bolted to the floor?
In most sites pallet racking should be bolted to the floor, and inspectors check the floor fixings as part of the inspection. The HSA says racking must be put up as per the maker’s instructions, ‘including appropriate security and anchorage’. On standard pallet racking, that usually means each base plate bolted down.
If a frame isn’t bolted down, it can shift when a truck catches it. The movement often only shows up at the next visit, as a twisted base plate or a frame that’s no longer straight. Our pallet racking anchor bolts come in packs of 50, and levelling shims for the embedded foot keep the upright straight where the floor isn’t level. The pallet racking safety guide on our blog covers set-up in more depth.
What do green, amber and red mean on a report?
SEMA’s traffic-light system rates racking damage green, amber or red. Inspectors often use it, and each colour has its own deadline, as the table below shows.
| Rating | What SEMA says it means | What you do |
|---|---|---|
| Green | Damage within SEMA’s limits | Note it and look again next visit |
| Amber | Damage bad enough to need repair | Once those spaces are empty, don’t refill them; repair within four weeks |
| Red | Serious damage | Unload it at once and stop using the bay |
Green still means damage and SEMA says it shouldn’t be ignored. An amber left unrepaired for four weeks automatically becomes red, so treat it as a four-week clock rather than a note for next year.
What happens after the report comes back?
When a racking inspection report comes back, deal with any red ratings first and work through the rest in this order:
- Unload any red bays straight away and stop using them.
- Leave emptied amber spaces empty and get the repair done within four weeks.
- Have trained racking fitters replace damaged parts with ones matched to your racking’s make.
- Record each repair and keep it with the report.
- Ask for the repaired bays to be checked before they’re loaded again.
SEMA also says inspectors still find uprights drilled or welded in ways the design never allowed, so step three matters. Our racking accessories cover the guards and fixings a repair list usually includes.
Free printable pallet racking inspection checklist
A pallet racking inspection checklist should record each fault against its location and give it a red, amber or green rating, so your team knows which bays to unload and when. Our free template works that way, and it also covers top rack safety issues the HSA flags, such as overloaded beams and missing load signs.
Download the RackZone Pallet Racking Inspection Template Checklist
The sheet lists the faults to look for on uprights, bracing, beams, decks, guards and load signs, with space for a location reference and notes against each one. Print a fresh sheet for each weekly check and keep it on a clipboard at the end of aisle one. It’s for your own checks and doesn’t replace the expert visit.
Each rating on the sheet comes with an action, as the key below sets out.
| Rating | What to do |
|---|---|
| Red risk | Offload immediately |
| Amber risk | Offload within 4 weeks and don’t reload until it’s repaired |
| Green risk | Monitor it and include it in future inspections |
| Other | Add notes or seek further advice |
Keep each completed sheet with your inspection reports. The law wants inspection results kept for five years, so keep these sheets as long. Our guide to the maintenance schedule racking needs covers the wider upkeep of racking beyond these checks.
So what should you do this week?
Naming your racking safety person and starting the weekly log are the two most useful jobs this week. Book the next expert visit if the last one was more than 12 months ago. A weekly log kept by someone on the floor tends to spot new damage long before the annual visit would.
We’re 100% Irish owned and deliver nationwide next day on orders before 3PM, Monday to Thursday. If you’re not sure which guard or fixing suits your racking, get in touch with our team or call +353 (0)90 9673261 and we’ll talk it through.
Disclaimer: This guide gives general information on Irish racking inspection requirements as of November 2026 and isn’t legal or professional advice. Check the HSA’s current guidance and have a competent racking inspector assess your own site.
